K&F Magic Arm Mini Grip with Dual Mini Super Clamp Heads | KF31.096

Clamp anywhere, position precisely, lock it down

K&F Concept Magic Arm Mini Grip with Dual Mini Super Clamp Heads | KF31.096 is built for content creators and videographers who need to mount cameras, lights, monitors, or microphones in locations where a traditional tripod or light stand won't fit. Clamp one end to a railing, table edge, tripod leg, or bicycle handlebar, position the magic arm to the exact angle you need, and lock it down. The dual-clamp design means you can anchor both ends for added stability, or use one clamp as a mounting point and the other as an accessory holder. The 18 to 60mm jaw range covers most practical surfaces, motorcycle handlebars, bicycle frames, desk edges, stair railings, light stands, tree branches, and tripod legs all fall within range. Whether you use both clamps or remove one and use the 1/4" thread, you so many setup choices. The 1.5kg load capacity supports a mirrorless body with kit lens, action camera, small LED panel, or field monitor, the gear mix typical of a solo creator or small production team. Multiple 1/4-inch expansion holes across both clamps and the magic arm let you stack accessories, a microphone on one clamp head, a small LED on the other, and a phone mount on the arm itself, all on one rig. The included action camera mount allows you to set up a camera for even more compatibility. The system disassembles completely, so you can use one clamp as a standalone reflector holder and the other with the arm for a separate setup on the same shoot.

1.5kg load capacity for mirrorless, action cameras and accessories
The 1.5kg load capacity covers most solo-creator setups: a mirrorless body with kit lens on one clamp head, a compact LED panel or microphone on the other, or an action camera with a small monitor attached. This threshold is comfortable territory for lightweight gear but not heavy telephoto lenses, full-size cinema monitors, or stacked accessory rigs that push the combined weight over 1.5kg. The dual-clamp design distributes load across both anchor points, reducing the sag or drift common with single-point clamp mounts. Most magic arms offer mounting points and configurability, but having two clamps allows for the holding of very awkwardly shaped equipment. Mounting an umbrella pole to a tripod leg is not something possible with standard photographic accessories. . The action camera adapter mounts GoPro cameras, DJI Osmo Action, Insta360 and any action camera following the GoPro mounting standard.

Dual clamps with 18 to 60mm jaw opening
The 18 to 60mm jaw range grips round and flat surfaces from thin railings to thick pipes, table edges, tripod legs, and tree branches. The non-slip silicone pads cushion the jaws to prevent scratches on painted metal, polished pipes, and glossy table edges, while increasing friction to stop the clamp sliding down smooth surfaces under load. This makes the clamp practical for location shoots where you're clamping to borrowed furniture, public railings, or outdoor structures without leaving marks. The dual-clamp design is the differentiator here: you're not just clamping to a surface and hoping the arm holds, you have the option to anchor both ends, which eliminates the droop or twist common with single-point mounts.

Magic arm with dual ball heads and 360° rotation
The magic arm articulates on two independent ball joints, locking at any angle with infinite positioning between the clamp points. This gives you the positioning freedom of a ball head but with the reach and rigidity needed to clear obstacles or achieve off-axis angles, overhead shots, under-table product reveals, side-mounted key lights. The central knob tightens the ball heads for quick adjustments, and the included Allen wrench lets you increase tension for heavier loads without the ball head creeping mid-shoot. The 360° rotation on both heads means you can position a monitor, light, or microphone exactly where you need it without repositioning the clamp itself, critical when you're shooting in a tight space or working alone.

Multiple 1/4-inch expansion holes for accessory stacking
The multiple 1/4-inch expansion holes across both clamp heads let you stack accessories without needing a separate cage or mounting plate. Attach a shotgun mic to one clamp head, a small LED to the other, and a phone mount to one of the expansion holes on the arm, all on one rig. This consolidation reduces the number of separate mounts you need to carry and simplifies setup when you're working alone. The expansion holes accept standard camera threads, so any accessory with a 1/4-inch tripod socket, microphones, LED panels, phone mounts, cold shoe adapters, small articulating arms, will fit.

Retractable anti-rotation pins for drift-free positioning
The retractable 1/4-inch Arri anti-rotation pins lock into threaded accessories to prevent rotation under load, critical when positioning a monitor or light at a precise angle and expecting it to stay there between takes. The pins retract when not needed for flat surfaces or accessories without registration sockets. This feature is the difference between a mount that holds position during a full day of shooting and one that drifts out of frame every time you adjust the camera. For creators using small monitors on gimbals or LED panels on moving rigs, the anti-rotation pins are the detail that keeps the setup stable under vibration.

Knob locking with Allen wrench tensioning
The knob locking mechanism tightens the ball heads for quick adjustments, and the included Allen wrench lets you increase tension for heavier loads without the ball head creeping under load. This two-stage system gives you the speed of a knob lock for repositioning and the security of a wrench-tensioned lock for heavier gear. The replacement rubber washers in the box are spares for when the originals wear after extended use, keeping the clamp working long-term without needing to source proprietary parts or buy a new clamp.

Non-slip silicone grip pads for surface protection
The silicone grip pads cushion the clamp jaws to protect surfaces and increase friction to prevent slippage on smooth materials. This makes the clamp practical for clamping to painted railings, polished pipes, glossy table edges, and other surfaces where a bare metal clamp would scratch or slide. The pads also grip better on round surfaces like handlebars or tree branches, reducing the risk of the clamp rotating under load. If you're clamping to a particularly delicate finish, test the grip on an inconspicuous area first.

343g aluminium-alloy construction for portability
The 343g weight balances strength with portability, light enough to carry in a camera bag without adding bulk but rigid enough to hold a mirrorless body or small LED panel without flexing. The aluminium-alloy construction is superior to plastic clamp-and-arm systems that feel flimsy and unreliable, while being less bulky than heavy-duty cinema clamps typically reserved for larger rigs. For creators who need a dependable mount that actually goes with them instead of staying in the studio, the 343g weight is the sweet spot.

Easy disassembly and modular expansion
The system disassembles into individual clamp heads and magic arm sections for independent use or reconfiguration. Use one clamp as a standalone mount and the other with the arm for different setups on the same shoot, one clamp holding a reflector on a light stand and the other with the arm positioning a fill light on a table edge. This modularity is useful when you need a simple reflector holder on a light stand (one clamp) and a separate phone mount on a table edge (the other clamp) during the same session. The ability to break the system into independent components also makes it easier to pack and transport.

The K&F Magic Arm Mini Grip with Dual Super Clamps | KF31.096 is a practical mounting system for content creators who need to position cameras, lights, monitors, or microphones in locations where a traditional tripod won't fit. With dual clamps, a magic arm, and multiple expansion holes, it's a versatile tool designed to support modern video production workflows. Order the KF31.096 today and take control of your setup with confidence.

Frequently Asked Questions

Frequently Asked Questions:
Q: Can I use just one clamp without the magic arm, or do they have to stay connected?
A: The system disassembles completely. You can use one clamp as a standalone mount, the other clamp independently, or connect both via the magic arm depending on what the shoot requires. This modularity is useful when you need a simple reflector holder on a light stand (one clamp) and a separate phone mount on a table edge (the other clamp) during the same session.

Q: Will this clamp damage painted railings or polished surfaces?
A: The silicone grip pads cushion the jaws to prevent scratches on painted metal, polished pipes, and glossy table edges. The pads also increase friction to stop the clamp sliding down smooth surfaces under load. If you're clamping to a particularly delicate finish, test the grip on an inconspicuous area first.

Q: Do I need to buy a separate GoPro mount, or is one included?
A: This model does include a GoPro mount in the box. You will not need and additional GoPro cage or adapter with a 1/4-inch thread (sold separately) to attach an action camera to either clamp head. The package includes the dual-clamp magic arm system, two replacement rubber washers, and an Allen wrench as well.

Q: How do I stop the ball heads from creeping when I mount something heavy?
A: Tighten the locking knob first, then use the included Allen wrench to increase tension on the ball head if you notice any drift under load. The wrench adjusts the internal mechanism to hold heavier accessories firmly without the ball head loosening mid-shoot. The replacement rubber washers in the box are spares for when the originals wear after extended use.

Q: Can I clamp this to a bicycle handlebar for POV footage?
A: Yes, the 18 to 60mm jaw range covers most bicycle handlebars, motorcycle grips, and scooter stems. The non-slip silicone pads grip the handlebar securely, and the retractable anti-rotation pins lock into your camera or action camera cage to prevent the mount twisting during movement. Keep the combined weight of your camera and any accessories under 1.5kg, and check that the clamp is fully tightened before riding.

Technical Specifications:
 - Maximum Load Capacity: 1.5kg
 - Jaw Opening Range: 18-60mm diameter
 - Ball Head Rotation: 360° on both heads
 - Thread Type: 1/4-inch screw threads with multiple expansion holes
 - Material: Aluminium alloy with non-slip silicone pads
 - Locking Mechanism: Knob locking with Allen wrench tensioning
 - Anti-Rotation Feature: Retractable 1/4-inch screw pins
 - Weight: 343g
 - Dimensions: 250 x 84 x 24mm
 - Included Accessories: 2 replacement rubber washers, Allen wrench